Shipping Notice

Henry Holsters will be closed from December 25 through January 4. Orders placed on or after December 24 will begin shipping out the week of January 5th.

We hope you have a Merry Christmas and a Happy New Year!

Henry Holsters Ember

Henry Holsters Ember

Compact, Light-bearing, Ambi, IWB/AIWB

IWB/AIWB Assembly Video

Detailed, step-by-step instructions

Enigma LB Assembly Video

Detailed, step-by-step instructions

Left Handed Setup Video

Detailed, step-by-step instructions

About the Ember

The Ember is designed to work as a stand alone, light-bearing, ambidextrous holster for use with either the Sig P365/365X/365XL or Glock G43x/G43/G48 with a Streamlight TLR-7-sub light.

Your Ember holster comes with a DCC Monoblock, attachment hardware and may come with the optional DCC Mod4 1.5in attachment kit. Please follow these simple instructions to properly assemble your Ember and contact us if you have any questions.

IWB/AIWB Assembly Instructions

YouTube video
Ember - DCC Monoblock Kit
Ember – Monoblock Kit
Ember - Monoblock Assembly 1
Ember – Monoblock Assembly
Ember - Monoblock Assembly 2
Step 1 – Insert Screw Post
Ember - Monoblock Assembly 3
Step 2 – “Capture” with Rubber Spacer
Ember - Monoblock Assembly 4
Step 3 – Repeat
Ember - Monoblock Assembly 5
Step 4 – Lay-over Monoblock
Ember - Monoblock Assembly 6
Step 5 – Attach with Screws
Ember - Monoblock Assembly 7
Step 6 – Tighten evenly

Monoblock (Standard)

Included hardware:

  • DCC Monoblock
  • 1/4in Flat head truss screws (2x)
  • 1/4in Rubber washers (2x)
  • 1/4in Screw posts (2x)

Step 1: Determine “Right Hand” or “Left Hand”. If Left, start here.

Step 2: Insert the screw posts through the holster from the inside (top slots for deep conceal).

Step 3: Use the rubber washers to “capture” the ends of the screw posts so that they don’t fall back out

Step 4: Lay the Monoblock over top of the rubber washers

Step 5: Insert Flat Head Truss screws through Monoblock and tighten

Ember - Mod4 Kit
DCC Mod4 Kit
Ember - Mod4 Assembly 1
Holster Orientation
Ember - Mod4 Assembly 2
Step 1 – Insert Screw Post
Ember - Mod4 Assembly 3
Step 2 – “Capture” with Rubber Spacer
Ember - Mod4 Assembly 4
Step 3 – Repeat
Ember - Mod4 Assembly 5
Step 4 – Lay-over Mod4 Clip
Ember - Mod4 Assembly 6
Step 5 – Insert screws, tighten
Ember - Mod4 Assembly 7
Step 6 – Repeat

Dual DCC Mod4 1.5in (Optional)

Included hardware:

  • DCC Mod4 1.5in (2x)
  • 1/4in Flat head truss screws (4x)
  • 1/8in Rubber washers (4x)
  • 3/16in Screw posts (4x)

Step 1: Determine “Right Hand” or “Left Hand”. If Left, start here.

Step 2: Attach DCC Mod4 clips to lower attachment holes using included hardware.

YouTube video

Enigma LB Assembly Instructions

Learn how to assemble, adjust, and wear a PHLster Light Bearing Enigma. Lots of adjustment instructions and tips and tricks for conceal carry as well as detailed instruction for initial setup. 


PHLster LB Enigma Instructions

Left Handed Setup

YouTube video

Modwing

The first step to setting up your Ember for left-handed carry is to switch the installed ‘Modwing’ to the left-hand setup.

  1. Remove the Modwing from your Ember holster
  2. Remove screw posts and insert them through the holster from the opposite side
  3. Disassemble your Modwing and re-install the “insert” from the opposite side
  4. Insert the eyelets into the Modwing (from the opposite side as originally inserted)
  5. Re-attach the Modwing to the Ember holster (from the opposite side as originally installed)

Belt Attachments

With the Modwing installed for left-handed carry you are now able to install your belt attachment hardware. Follow the guides (above) using the opposite/reverse side.

P365-XMACRO Rail Key Swap

YouTube video